Attic Insulation in Spring, TX

Measure Blown-In Fiberglass Insulation Spring TexasThe attic insulation in your home should be at a minimum depth in order to be energy efficient. At Spring Insulation, LLC, we know exactly the amount of attic insulation you need for your home to be optimized for energy efficiency. Our team of insulation installers will be sure to give you the best price and keep your insulation cost at a minimum. You need to ensure that the attic insulation r-value is within the recommended range. It’s very possible that you need a complete attic insulation removal and replacement. You’ve come to the right place because we have all of your insulation needs taken care of.

Understanding Attic Insulation

Prior to making any comparisons between different types of attic insulation, you need be familiar with the terminology used to describe the insulation material.

In order to prevent heat from escaping from your building, you need insulate the attic area. Efficacy in reaching that objective is measured by the R-Value of a substance.

Where you live and the climate influence how much R-Value insulation your attic has to have. Those living in hot or cold regions should use an R30, while those living in the midst of the two should use an R49.

Types of Attic Insulation

Roof-Fiberglass-Insulation-Spring-TXThere are many ways to skin a cat, says the old proverb: When it comes to attic roof insulation, your options are just as diverse. Attic insulation installation may make a big difference in whether or not you have enough money saved for a summer vacation or whether you have to spend it all on your utility bills.

Continue reading to learn about the many types of attic insulation. We’ll discuss their benefits and drawbacks, and which one is most likely to keep your thermostat in balance. Below are some of the most common types of attic insulation on the market.

Fiberglass Batt Insulation

Fiberglass is by far the most popular choice for attic insulation because of its great fragility. Plus, it’s made from recycled materials and sand. To make fiberglass batts (huge rolled-up sheets of insulation), manufacturers use reflective foil backing or paper to keep the sheets bound together with an adhesive vapor barrier.

Fiberglass batts offer certain advantages, especially for new construction with attics that have never had any insulation added before (as well as gut renovations). There are several advantages to using fiberglass batts:

  1. Fiberglass insulation tends to withstand moisture well despite the fact that it isn’t water-proof. Because of this, mold and mildew have less of a chance of growing on it.
  2. Fiberglass is noncombustible.  You don’t have to worry about installing it adjacent to your attic’s timber construction. Fiberglass is fire resistant.
  3. Ease of Installation – Fiberglass Batts may be easily picked up and rolled up. Because of their size, they can quickly and effectively cover a large area. They are therefore a great choice for new building, provided they are put correctly.

Other Batt Insulation Types

As the most popular type of insulation batt, fiberglass has dominated the market for a long time. Batts like as these have been increasingly popular over time:

  • Mineral Wool – Mineral wool is naturally fire resistant and would require 1,800 degrees Fahrenheit in order to ignite. It’ll keep you warm even if it’s drenched to the skin. Sound-absorbing mineral wool has long been used, but it’s becoming harder to obtain due to a decline in popularity.
  • Denim Insulation – Denim insulation is made from recycled blue jeans! It’s likely that the identical pants you wore in your fashion cycle are now helping to insulate your attic.
    Because of its environmental friendliness, denim insulation is quickly becoming a popular choice among ecologically aware customers.. The only problem is that despite its popularity, it is prohibitively pricey.

Blown-In Fiberglass Insulation

Blown-Between-Joists-Insulation-Spring-TXFor loose-fill insulation, you may buy fiberglass in little bits that are bundled in huge sacks. A blowing machine distributes the pieces to fill up any gaps that may exist after they are removed from the truck. It may seem different, but blown-in fiberglass is still the same material as batts. This means that it has the same drawbacks and safety risks.

Despite popular belief that blown-in fiberglass loses R-value below 20 degrees Fahrenheit due to a 1990s research, this has recently been demonstrated to be untrue.

Using fiberglass blown insulation may be a good idea for a variety of reasons, including the following:

  • Blown-In Attic Insulation is superior than batts because it can fit into tiny spaces around cables, pipes, and other awkwardly framed areas better than traditional batt-style insulation.
  • It’s inexpensive – For the money, it’s difficult to beat the value of blown-in insulation.
    It may seem different, but blown-in fiberglass is still the same material as batts. This means that it has the same drawbacks and safety risks.

Cellulose Insulation

Cellulose Blown In Attic Insulation SpringCellulose is created from newspaper shreds that have been ground to an ultra-fine powder. The only reason cellulose is seen as a simple and cost-effective solution is because of the marketing it has received throughout time. There are a number of reasons why blown-in cellulose is the poorest possible choice for insulation. Cellulose is often considered an excellent choice, yet there are several reasons why it is not:

  • Cost-Effective Alternative – In spite of having a greater R-Value than the majority of fiberglass, cellulose is often far less expensive.. A typical savings of up to one-fourth of what you’d pay for fiberglass is achieved by using cellulose instead of it. Despite the fact that cellulose is an extremely cost-effective material, it is so…
  • Chemical Treatment — Manufacturers of blow-in cellulose promote the fact that their cellulose has been treated with boric acid, making it rat and insect resistant. This is a complete fabrication. Even with the high concentration of boric acid in cellulose, rodent and insect activity is virtually unavoidable. Cellulose producers have been instilling this notion in the minds of their consumers for many years.

Also, keep in mind that cellulose is made to retain and absorb water. Mold, mildew, and rotting will have a field day in this place. The use of cellulose insulation without a vapor barrier is highly discouraged because of this.

Spray Foam Insulation

Foam-Installation-Spring-TXSpray foam is unrivaled as an insulator. Both open- and closed-cell versions are available, with the closed-cell version boasting a staggering R-Value of seven! Spray foam insulation has several advantages, including the following:

  • Long-Lasting Airtight Seals – Spray foam expands rapidly when used, creating a vault-like seal that keeps out moisture and contaminants. And once it’s up, it’s here to stay. While most insulating materials need to be changed every 10 years or so, foam may work at its best for decades before needing to be re-inflated. In other words, you may set it and forget it.
  • Foam is fundamentally anti-cellulose when exposed to moisture, hence no water is allowed. It’s completely impervious to liquids of any kind.
  • The ability of foam to increase your building’s envelope, or the physical gap between its conditioned area (the space used by humans) and unconditioned space, sets it apart from other types of insulation.

Adding spray foam to your building’s exterior improves the structure while acting as a sound barrier as well.

Spray foam’s primary drawback is that it hardens and cannot be removed in a domestic setting, which limits its usefulness. By covering wiring, pipe, and other impediments in the attic that may need to be treated at a later time, you will lose the ability to recover them. Spray foam, on the other hand, is prohibitively costly, and as a result, it’s typically employed in commercial buildings with high vaulted ceilings rather than homes without an attic.

Other Attic Insulation Types

If you’re looking for a different approach to attic insulation, consider some of these other viable options:

  • Rigid Foam Board Insulation – This is a panel particularly intended to reduce the flow of heat between joist studs in your attic. Since they’re stiff, they’re easy to work with and may be easily trimmed down to size.
  • Radiant Barrier – Although not strictly insulation, radiant barriers might be the appropriate solution for you if you live in a hot climate. Other insulators function to retain heat inside the house, but these barriers are put on the bottom of the roof and covered with reflective material (such as aluminum foil) to keep heat outside the house. If you want to save money on cooling, this is a great solution.

Attic insulation may be installed in a variety of methods. There are a plethora of ways to do it wrong. Spring Insulation, LLC is happy to assist you.

Insulating your attic doesn’t have to be a problem when you choose us. We’re a top-rated company for both insulation installation and insulation removal.

Copyright 2021